مدل توربین بادی موتوردار با ارتفاع 520mm در مقیاس HO/TT/N
Wind turbine model, 520mm height (HO/TT/N scale), motorized
طراح: positron
قیمت فایل با خرید و تحویل
۱٬۵۳۵٬۰۰۰ تومان
- قیمت ارزی فایل
- ۴.۵ EUR
- معادل تومانی
- ۱٬۳۲۳٬۰۰۰ تومان
- کارمزد خرید
- ۲۱۲٬۰۰۰ تومان
بعد از پرداخت، فایل را برایتان میخریم و در صفحهٔ همین سفارش در حساب شما برای دانلود میگذاریم. چند فایل را با هم در سبد بخرید تا کارمزد یکبار گرفته شود.
مجوز: CULTS PU - Private Use — فقط استفادهٔ شخصی؛ فروش محصول چاپشده مجاز نیست
این طرح کار طراح آن است و مجوز استفادهاش همان مجوز طراح است؛ پخش یا فروش خود فایل مجاز نیست.
دربارهٔ این مدل
This is a model of a typical European land wind turbine. Its height from ground to blade tip is 521mm, blade length is 200mm. Since real-world wind turbines vary in side widely, the model can be used on dioramas and layouts of different scale: H0 (1/87), TT (1:120), N(1:160), probably Z (1:220). This and more info can be found on project page: https://positron96.gitlab.io/projects/wind-generator Video in action and assembly instructions can be found here: https://youtu.be/pb3LNoZAD5o The model is designed to be printed on typical 220mm printer bed (e.g. Ender 3 or Prusa). The tower itself is split into 3 parts, upper parts should be glued together, the lowest part is held with friction, so that the upper part of model can be rotated or detached from the layout for transportation. The model is designed to be motorized with a popular N20 gear motor. I've tested several gear rations and voltages, so far 60 RPM 12V motor powered with 5V produces very good results. Downvoltage to 5V makes the operation very quiet (to make it quieter, lubrication is advised). Also 5V can be easily obtained from, e.g. smart phone charger or USB power bank. My instance of motor draws around 10 mA of current (yes, 10 mA). Part list: * 1x N20 DC Gearmotor (12V, 60 RPM), sample link: https://www.aliexpress.com/item/33022320164.html * 1x M3x16 countersunk screw * Parts 1.1 (or 1.1B), 1.2, 1.3 for the tower. Part 1.1B has M12 thread at the bottom, so it can be screwed to the layout. Part 1.1 just has a 30mm height 12mm diameter mounting pin and needs to be glued to the layout). Glue parts 1.2 and 1.3 together, but do not glue 1.1. The upper part is designed to be friction-fitted into lower part, so that the model can be disassembled for transportation of the layout or rotated. The electric connector needs to be placed in the cavity in the lower tower part (see picture) * Parts 2.1 and 2.2. Glue part 2.2 to the nacelle. No glue required, top slides into slot in the bottom and is secured by M3 screw. * Parts 3.1 and 3x 3.2 for the fan. Glue blades into the hub with CA, epoxy or PVA. Fan is friction-fitted to the shaft of the motor. There is a guideway to place an LED on top of the nacelle. It is not a through-hole by default, so you need to drill the hole through the surface. I tested with 0805 SMD blinking red LED, the result looks very good (in the video). 3mm through-hole LED can be installed if you increase a hole to 3.2mm by drilling. Place the resistor near the LED, then you can power both the motor and LED by one pair of 5V wires. Flyback diode across the motor is also recommended. ### Layer height * 0.08mm layer for the blade for highest surface quality. * 0.2mm layer for other parts ### Orientation: * Print blade thin long edge facing up * Nacelle top needs to be printed upside down * Other parts are obvious and are mostly printed upside up. ### Supports * Blades need supports * Nacelle bottom requires supports if you print it upwards, as not all of the bottom surface touches the bed * Other parts don't require supports **File "Hub.stl" is exported as-designed and is not parallel to build plate! Use "Lay flat" function in your slicer.**
- model railroad
- diorama
- wind turbine
- tower
- wind
- generator
- power
- ho_scale
- 1/87
- 1:87
- ho
- ho scale
- 1/76
- 1:76
- 1/120
- 1:120
- 1/160
- 1:160