رفتن به محتوای اصلی
ارسالات ترکیه: ۸ تا ۱۲ روز کاری

آداپتور لنز Video B4 به مانت Micro four-thirds، 2/3" و 1/2"

Video B4 (2/3" and 1/2") lens to Micro four-thirds mount adapters

طراح: vintage-lens

قیمت فایل با خرید و تحویل

۶۴۱٬۰۰۰ تومان

قیمت ارزی فایل
۱.۵ EUR
معادل تومانی
۴۴۱٬۰۰۰ تومان
کارمزد خرید
۲۰۰٬۰۰۰ تومان

بعد از پرداخت، فایل را برایتان می‌خریم و در صفحهٔ همین سفارش در حساب شما برای دانلود می‌گذاریم. چند فایل را با هم در سبد بخرید تا کارمزد یک‌بار گرفته شود.

مجوز: CULTS PU - Private Use — فقط استفادهٔ شخصی؛ فروش محصول چاپ‌شده مجاز نیست

این طرح کار طراح آن است و مجوز استفاده‌اش همان مجوز طراح است؛ پخش یا فروش خود فایل مجاز نیست.

دربارهٔ این مدل

This is a two part adapter that bolts on to the existing B4 flange on the lens and provides a parfocal mount to M4/3rds (Lumix, BMPCC etc). It is not intended to support a B4 lens via the M4/3 mount !!! (they are mostly too heavy), however, the adapter will easily support small DSLRs via the lens. The clamp requires 6 off M2.5x15mm screw/bolts and lock nuts for the captive nut recesses (note: this is the same STL for both the standard B4 and B4/½ inch flanges). When clamped together the two parts ensure a tight grip on the B4 flange, do not overtighten; a small gap has deliberately been left so you can adjust the pressure around the mount (any over tightening will be apparent by squashing the gap). Parfocal adjustment is assumed to be on the lens (eg Canon J9ax5.2B4, Canon J15ax8B4 etc -where there is 1mm of adjustment), this adapter should put the lens in the centre of the 1mm adjustment range. NEW: B4-half-inch>M43(v3)BARREL v2.stl Includes adapter for ½" video lenses (eg Canon H15sx6). These use a similar "B4" bayonet, but the flange distance is 12.26mm shorter. ½" bayonet flanges can be recognised by their slightly larger (3.4mm dia) locking pin. *[It has been noticed this adapter doesn't work with Sony 1/2 inch ENG lenses, eg the Canon PH14ax6.6B, and a deeper+wider cut-out is required on the lens side of the adapter. Message me if this is required.]* NEW-2: B4-halfinch>B4 adapter (v1).stl: adapter to use B4 lenses on ½" camera bodies (untested, but should work as requested...) The assembly video shows the B4 to e-mount adapter, but assembly is essentially the same. FDM prints: The clamp part should be printed, with support, with the captive nut cage on the build plate (this should ensure a smooth surface against the lens' B4 flange). The print might look better printed the other way up, if so, ensure the recess for the B4 flange is free of print material and flat against the mount. The M43 mount/B4 adapter STL can be printed with the M43 mount on top and without support, though, I find "with support" works fine and gives a slightly better M43 flange. The slicer should only recommend support for the flanges and use very little material. The 1/2" adapter has also successfully been printed in SLS, PA12 Nylon.

  • lens
  • b4
  • m43
  • micro four thirds
  • adapter
  • video
  • eng lens
  • half-inch lens