TROY'S 3D PRINTED RC CRJ-900/CRJ-700 AIRLINER
طراح: TroyMcMillanRC
قیمت فایل با خرید و تحویل
۲۰٬۱۴۶٬۰۰۰ تومان
- قیمت ارزی فایل
- ۵۹.۰۷ EUR
- معادل تومانی
- ۱۷٬۳۶۷٬۰۰۰ تومان
- کارمزد خرید
- ۲٬۷۷۹٬۰۰۰ تومان
بعد از پرداخت، فایل را برایتان میخریم و در صفحهٔ همین سفارش در حساب شما برای دانلود میگذاریم. چند فایل را با هم در سبد بخرید تا کارمزد یکبار گرفته شود.
مجوز: CULTS PU - Private Use — فقط استفادهٔ شخصی؛ فروش محصول چاپشده مجاز نیست
این طرح کار طراح آن است و مجوز استفادهاش همان مجوز طراح است؛ پخش یا فروش خود فایل مجاز نیست.
دربارهٔ این مدل
This is a fully 3D printed CRJ-900 I designed to be easy to assemble and fun to fly. You can also build this as a CRJ-700 if you would like. All you need to do is leave out fuselage part 3. I have not built on and test flown it myself so make sure to send me some picture if you build on for yourself. Build Volume required for this airplane is 200x200x200. RTF weight: 3,300g (PLA 2x 4s 2200mah) Wingspan: 1.5m Length: 2m Print time: 120hrs 2kg of PLA I have a full step by step assemble guide on my YouTube channel. https://youtu.be/D8aDJ5Wal5c Here is an rcgroups build thread: https://www.rcgroups.com/forums/showthread.php?4396017-Troy-McMillan-CRJ-700-900 This plane has flaps and retractable landing gear. I designed this to use a 6ch receiver. A key feature that allows this to happen are the special design of the servo brackets that allow you to mount the servos in any orientation. This makes it possible to use a y harness to connect all the control surfaces. If you have the ability to use more channels I would recommend that for the flaps and ailerons so an 8ch setup would be ideal but if you only have access to 6ch it will work great. I do not use any carbon fiber rods in this build to make it easy to source the parts required. There is a spar intentionally designed into the wing sections, that make it very strong. I did add a location to add a 8mm x 500mm carbon fiber tube if you would like to add a traditional spar. I designed a NEW 70mm EDF engine Nacelle for this CRJ-900. The 64mm required full power to get off the runway for the maiden flight with not much extra power. Basically almost flew to scale, for RC models it is good to have a bit of excess power if needed. This will allow for a bit shorter takeoff role and be more efficient to fly. You can still use 64mm if you would like to. The 64mm will be ok for LW or regular PLA it will just be a bit more difficult to fly. I would say if you are using regular PLA I would recommend the 70mm EDFs and if you are using LW-PLA you can use the 64mm EDFs. Here is the link to the 70mm EDFs I used with 80amp ESC. https://amzn.to/3YZ2UIw *If you would like to print the wing using LW-PLA it will save around 1000grams, but it is not required. I have not flown it in LW-PLA, but I designed it with LW-PLA in mind. Printing it fully out of PLA shows how well it flies with that additional weight. I printed an entire one out of LW-PLA and made sure I could set the CG. I have not flown it yet but I will be sure to and add a video for you. ** LANDING GEAR ** For the landing gear as you can see from my maiden flight the 3d printed struts did not hold up. I did make them a standard length to hopefully make easy to find aluminum gear. The nose strut is 50mm from the top of the strut to the center of the axle with 30mm diameter tires. The main strut is 60mm from the top of the strut to the center of the axle with 50mm diameter tires. The shank from the retracts is 4mm. I have a complete list of parts required for this build on my YouTube assembly guide. Here is a link to the Decals: Coming soon! All The Fuselage Parts are designed with a 15mm ring this is a key feature for strength so before you print the parts make sure this ring shows up on your slicer software. Fuselage 1-10 Print will 15mm ring on the build plate. Set the Extruder closer than standard to the bed. This is also referred to as Z-Offset, I set mine up so the extruder is almost touching the bed. The first layer will print on the bed without the 15mm ring, the second layer will start a 15mm ring. You want the second layer to adhere to the bed, the first layer does not matter. Turn off skirts or brims. **FUSELAGE** Fuselage 1-11: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 0 Bottom Layer - 4 Initial Bottom Layer - 0 Extra Skin Wall Count - 5 Skin Removal Width - 3.5 mm Infill Density - 0% Surface Mode - Normal Build Plate Adhesion Type - None Battery Hatch: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 5 Bottom Layer - 5 Initial Bottom Layer - 5 Extra Skin Wall Count - 0 Skin Removal Width - 5mm Infill - 0 Surface Mode - Normal Front Window Frame & Windows: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 10 Top Layer - 5 Bottom Layer - 5 Initial Bottom Layer - 5 Extra Skin Wall Count - 5 Skin Removal Width - 3.5 Infill - 0 Surface Mode - Normal **WING** Center Wing 1 & 2 , Left & Right Wing 1: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 0 Bottom Layer - 0 Initial Bottom Layer - 0 Infill - 0 Surface Mode - Normal Left & Right Wing 2-4: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 0 Bottom Layer - 4 Initial Bottom Layer - 0 Infill - 0 Surface Mode - Normal Wing Tip: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 0 Bottom Layer - 4 Initial Bottom Layer - 4 Infill - 0 Surface Mode - Normal Flap Gap: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 4 Bottom Layer - 4 Initial Bottom Layer - 4 Extra Skin Wall Count - 0 Skin Removal Width - .42mm Infill - 0 Surface Mode - Normal Left & Right Ailerons, Inner & Outer Flaps: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 0 Bottom Layer - 4 Initial Bottom Layer - 4 Extra Skin Wall Count - 0 Skin Removal Width - 1.5mm Infill - 0 Surface Mode - Normal **TAIL** Vertical Stabilizer: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 0 Bottom Layer - 0 Initial Bottom Layer - 0 Infill - 0 Surface Mode - Normal Vertical Stabilizer Top: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 10 Bottom Layer - 4 Initial Bottom Layer - 0 Extra Skin Wall Count - 0 Skin Removal Width - 3mm Infill - 0 Surface Mode - Normal Rudder: Layer Height - 0.2 *Initial Layer Height - 0.15 Wall Line Count - 1 Top Layer - 4 Bottom Layer - 4
- crj
- crj-900
- crj-700
- troy mcmillan
- 3d printed
- rc
- airplane