رفتن به محتوای اصلی
ارسالات ترکیه: ۸ تا ۱۲ روز کاری

آتل پای جلو برای سگ‌های کوچک

Front leg / Paw splint for small dogs

طراح: CreativeMindworksEngineering

قیمت فایل با خرید و تحویل

۱٬۳۷۴٬۰۰۰ تومان

قیمت ارزی فایل
۳.۹۹ EUR
معادل تومانی
۱٬۱۷۴٬۰۰۰ تومان
کارمزد خرید
۲۰۰٬۰۰۰ تومان

بعد از پرداخت، فایل را برایتان می‌خریم و در صفحهٔ همین سفارش در حساب شما برای دانلود می‌گذاریم. چند فایل را با هم در سبد بخرید تا کارمزد یک‌بار گرفته شود.

مجوز: PU - Private Use — فقط استفادهٔ شخصی؛ فروش محصول چاپ‌شده مجاز نیست

این طرح کار طراح آن است و مجوز استفاده‌اش همان مجوز طراح است؛ پخش یا فروش خود فایل مجاز نیست.

دربارهٔ این مدل

## ⚠️ DISCLAIMER **This is _not_ an approved medical product.** However, it significantly helped in the individual healing process of our Yorkshire Terrier puppy and saved us from a very expensive surgery. **Use at your own risk and responsibility.** --- Our Yorkie puppy suffered a broken front paw — all four middle paw bones were fractured in a straight, clean break. The vet initially improvised a brace, but our puppy quickly managed to remove it. That’s when we developed this custom splint design, integrating several features for better stability and adaptability: - 🦴 Flat bottom surface for walking - 🛡️ Reinforced sidewalls - 🔗 Openings for attaching Velcro straps - 🧷 Top slot to secure the brace and prevent slipping - 🌀 Riffled surface to help wraps stay in place At the start of treatment, our puppy weighed about **1 kg**. After 7 weeks in the cast, she grew to around **1.7 kg**, and her leg grew significantly. To keep up with the changes, I gradually scaled up the print in **Cura**, adjusting every few weeks. I brought several versions to the vet for professional application. The vet was genuinely impressed with how well it worked. While the puppy was supposed to stay still for weeks — ideally confined to a box — this was nearly impossible. Thanks to the splint, she was even able to walk a bit (though limited movement was still recommended). **Application process by the vet:** 1. Wrapped medical cotton around the leg (including between the toes) 2. Applied the brace 3. Secured with stretchy medical wrap 4. Wrapped around the body to prevent slipping **Result:** ✅ Her paw healed *perfectly*. 🐶 **Looking for a matching splint for the hind leg?** Check out the **[Hind Leg Splint for Small Dogs](https://cults3d.com/en/3d-model/tool/back-leg-splint-for-small-dogs)**, designed with a reinforced rear section and the same customizable fit. --- ## ⚠️ DISCLAIMER (repeated intentionally) This is _not_ a medically approved product. It worked well in our specific case but is shared here for informational and personal use only. **Always consult a veterinarian before use.** Use at your own responsibility. ## 🖨️ 3D Printing Recommendations - **Material:** Printed successfully in **PLA**. It’s easy to work with and strong enough for this use case. - **Layer Height:** Layer height isn't critical, but smoother surfaces are more comfortable for the puppy. I used between **0.1 mm and 0.25 mm**, depending on how much time I had. Lower layer heights reduce roughness and help minimize rubbing. - **Infill:** **20%** infill provided a good balance between strength and flexibility. - **Supports:** ✅ **Supports are required** Make sure support structures are **only on the outside** of the splint. Avoid internal supports that might affect fit or comfort. - **Scaling:** If your puppy is growing, consider printing **scaled versions** over time. I used **Cura** to gradually increase the size as my dog grew.

  • dog brace
  • dog splint
  • leg splint
  • dog front leg
  • small dog
  • yorkie
  • yorkshire terrier
  • puppy injury
  • pet orthotic
  • pet medical device
  • dog fracture
  • broken leg dog
  • dog rehabilitation
  • pet mobility
  • dog injury recovery
  • veterinary splint
  • animal cast
  • orthopedic pet
  • canine orthotic
  • cat
آتل پای جلو برای سگ‌های کوچک (Front leg / Paw splint for small dogs) — فایل پرینتر سه‌بعدی (STL)