رفتن به محتوای اصلی
ارسالات ترکیه: ۸ تا ۱۲ روز کاری

مدل چاپ سه‌بعدی داکت فن هات‌اند Ender 3، 3 V2، 3 pro و 3 max

Ender 3, 3 V2, 3 pro, 3 max, dual 40mm axial fan hot end duct / fang. CR-10, Micro Swiss direct drive and bowden compatible. No support needed for printing

طراح: BrissMoto

قیمت فایل با خرید و تحویل

۶۲۱٬۰۰۰ تومان

قیمت ارزی فایل
۱.۴۳ EUR
معادل تومانی
۴۲۱٬۰۰۰ تومان
کارمزد خرید
۲۰۰٬۰۰۰ تومان

بعد از پرداخت، فایل را برایتان می‌خریم و در صفحهٔ همین سفارش در حساب شما برای دانلود می‌گذاریم. چند فایل را با هم در سبد بخرید تا کارمزد یک‌بار گرفته شود.

مجوز: CULTS PU - Private Use — فقط استفادهٔ شخصی؛ فروش محصول چاپ‌شده مجاز نیست

این طرح کار طراح آن است و مجوز استفاده‌اش همان مجوز طراح است؛ پخش یا فروش خود فایل مجاز نیست.

دربارهٔ این مدل

طراحی Briss Moto برای رفع هرگونه ابهام، طرح‌های من تحت حمایت قوانین حق نشر هستند. توزیع یا فروش هیچ‌یک از طرح‌های من بدون دریافت مجوز کتبی قبلی از خودم مجاز نیست؛ حتی اگر طرح اصلی من را تغییر داده باشید. سپاسگزارم. با NEO سازگار نیست 2022-04-20: مدل‌های Ender 3v2 نسخه V4.41. پایه‌ی محل نصب CR touch روی Ender بزرگ‌تر شد و برای نگه‌داشتن مهره در fang، در سوراخ پشتی هم اصلاحی انجام شد. 2022-03-30: محل برآمدگی مدل‌های ریل خطی MS اصلاح شد. 2022-03-13: مدل Aquila نسخه 4.41 با محل صحیح سوراخ‌ها به‌روزرسانی شد. اما نمی‌توانم آن را با پروب‌های ترازکننده سازگار کنم؛ محل سوراخ‌ها با آن‌ها تداخل دارد. 2022-01-31: به من اطلاع داده شد که ممکن است ارتفاع پایه‌ی CR touch مشکل داشته باشد. پایه‌ی روی fang واقعاً 1.5mm بلندتر از پایه‌ی فلزی همراه دستگاه Creality است. اما وقتی CR touch کاملاً باز شده باشد، باید فاصله‌ای 2mm بین نازل و صفحه وجود داشته باشد. در طراحی fang در نظر گرفته شده که ارتفاع آن 1.5mm بیشتر از نازل باشد. اگر fang شما از این مقدار بلندتر است، ممکن است مشکل از همین باشد. در هر صورت، فایل «CR touch spacer» را به فایل‌های STL اضافه کردم تا کسانی که می‌خواهند ارتفاع پایه‌ها دقیقاً مطابق تنظیم Creality باشد، بتوانند از آن استفاده کنند. BL touch از CR touch بلندتر است و احتمالاً به این فاصله‌دهنده نیازی ندارد. از همه بابت بازخوردها سپاسگزارم. 2021-11-25: به‌روزرسانی V4.4 برای Ender 3 pro، Ender 3 max و Ender 3 مجهز به ریل خطی microswiss. fang نسخه V4.4 با پایه‌ی یکپارچه‌ی BL/CR touch؛ سوراخ‌ها از سطح قطعه عبور نمی‌کنند و دلیل مشخصی دارد. یک لایه‌ی تکی جلوی عبور سوراخ را می‌گیرد و امکان چاپ پل‌ها را فراهم می‌کند تا برای چاپ درست این قسمت به ساپورت نیازی نباشد. سپس لایه‌ی تکی را می‌بُرید تا سوراخ‌ها باز شوند. این کار را انجام دادم چون چاپ پلی که در وسط آن سوراخ دارد، ظاهر خوبی پیدا نمی‌کند؛ یا باید ساپورت اضافه کرد که زمان چاپ را بی‌دلیل زیاد می‌کند. با این روش قطعه بدون ساپورت خوب چاپ می‌شود و فقط 10 ثانیه طول می‌کشد تا لایه‌ی تکی را ببُرید و مسیر پیچ‌ها را باز کنید. از آن لذت ببرید :) 2021-11-14: نسخه‌های V4.4 برای Voxelab Aquila، از جمله مدل‌های دارای پایه‌ی BL-touch / CR-touch. 2021-11-13: نسخه‌ی جدید V4.4 با زاویه‌ی نوک اصلاح‌شده برای جهت‌دهی بهتر جریان هوا و پایه‌ی داخلی BL-touch/CR-touch به‌همراه سوراخ پیچ اضافه برای استحکام بیشتر (Offset: X = 44mm، Y = 7.5mm). برای Ender 3 V2 و کیت direct drive مدل ender 3 microswiss. به‌روزرسانی مدل‌های دیگر در ادامه ارائه می‌شود. برای چاپ مدل دارای پایه‌ی داخلی CR-touch دیگر اصلاً به ساپورت نیاز نیست. یک برجک کوچک ساپورت درون مدل تعبیه شده که در پایان کافی است آن را جدا کنید. همچنین فاصله‌دهنده‌ی Microswiss DD را بدون سوراخ‌های پیچ تنظیم extruder اضافه کردم. 2021-05-04: اضافه‌شدن Fan duct up V2 که توری در قسمت بالایی دارد. چاپ آن از مدل اصلی دشوارتر است، بنابراین هر دو فایل را اینجا نگه می‌دارم. 2021-05-01: اضافه‌شدن مدلی سازگار با Voxelab Aquila و مدلی سازگار با کیت ریل خطی Microswiss. هنوز باید یک آداپتور BL touch برای Aquila طراحی کنم. V4.2 - اکنون با micro swiss direct drive M2601 M2602 سازگار است. باید fang، فاصله‌دهنده و پیچ تنظیم extruder را چاپ کنید. (در یکی دو هفته‌ی آینده پایه‌ی BL touch برای این پیکربندی را آماده می‌کنم.) - همه‌ی مدل‌ها با چراغ‌های LED یکپارچه در دسترس هستند (LEDهای کلاهکی 5mm در جلو و امکان نصب یک LED ستاره‌ای 20mm در داخل). هر دو فایل، با چراغ و بدون چراغ، موجود است. چاپ مدل چراغ‌دار کمی دشوارتر است و جزئیات کوچکی دارد. - زبانه‌ی پیچ میانی بزرگ‌تر، محکم‌تر و چاپ آن آسان‌تر شد (برای Ender 3 pro و Microswiss). - سوراخ سیم فن جلویی به‌شکل شیار درآمد. V4.1 - محل نصب برای Ender3 و Ender 3 pro کمی تغییر کرد. اکنون فایل آن‌ها با Ender 3 V2 متفاوت است. - شیاری برای سیم‌های فن جلویی اضافه شد. 2021-02-04: یک قطعه‌ی الحاقی کوچک و اختیاری اضافه شد که زیر فن hot end قرار می‌گیرد و کانال را کامل می‌کند تا حداکثر بازدهی ممکن حاصل شود. این قطعه را جدا از fang نگه می‌دارم، چون یکپارچه‌بودن آن چاپ بدون ساپورت را ناممکن می‌کند. پس از چاپ، آن را در جای خود بچسبانید. با fang نسخه‌های V3 و V4 سازگار است. نام فایل STL: BRISS fang V3 V4 flow control. نسخه‌ها: V4.0 هندسه‌ای مشابه V3 دارد، اما برای چاپ‌پذیری بهتر تغییرات جزئی در آن اعمال شده و سوراخی برای Ender 3 pro اضافه شده است (+ براکت BL touch برای 3 pro) - زائده‌ای در میانه‌ی فن خنک‌کننده‌ی قطعه اضافه شد تا تلاطم هوا کاهش یابد و بازدهی بهتر شود. - fang کمی به سمت چپ جابه‌جا شد تا روی hot end بهتر در مرکز قرار بگیرد. - قلاب‌ها کمی کوتاه‌تر شدند (نقاط اتصال در سمت راست) تا نصب آسان‌تر شود. - زائده‌ی فن بالایی دوباره کامل شد تا چسبندگی به صفحه‌ی چاپ بهتر شود. - پلی برای اتصال دودکش به فلنج فن بالایی اضافه شد تا به افرادی که با مشکلات چسبندگی روبه‌رو هستند کمک کند. - در کانال خنک‌کننده‌ی hot end بریدگی‌ای ایجاد شد تا هنگام چرخاندن و جا زدن، پیچ به آن گیر نکند و نصب آسان‌تر شود. - سوراخ سیم‌های فن جلویی کمی بزرگ‌تر شد تا بتوان چند فیش bullet کوچک را از آن عبور داد. - سوراخ دومی در پشت اضافه شد که با صفحه‌ی پشتی اصلی Ender3 / Ender3 Pro هم‌راستا است. - براکت BL touch مخصوص هر نسخه ویرایش 2021-01-03: فایل STL کانال فن جلویی را اضافه کردم تا از مکش تمام خرده‌ریزها و رشته‌های فیلامنت از صفحه‌ی ساخت جلوگیری شود. بدون ساپورت چاپ می‌شود؛ فقط آن را صاف روی فلنج فن قرار دهید. برای نصب به پین‌های فشاری بلندتر نیاز دارید (نام فایل STL: «holder pin 4020 fan + duct»). V3.0 کانال‌های بسیار بزرگ‌تری نسبت به V2 دارد. هوای بسیار بیشتری به قطعات شما می‌رساند. کانال همچنین عریض‌تر است تا هنگام چاپ خطوط مستقیم در جهت Y، قطعه را به‌خوبی خنک کند. براکت‌های BL touch مخصوص هر نسخه هستند. fang باریک و جمع‌وجور امکان استفاده از دو فن 40mm را فراهم می‌کند. چاپ و استفاده از آن آسان است؛ یک قطعه‌ی یکپارچه است که مانند قاب فن اصلی Ender 3 v2 متصل می‌شود. وارونه و بدون هیچ ساپورتی چاپ می‌شود. می‌توانید از فن‌هایی با ضخامت 10 یا 20 mm استفاده کنید. فایل STL پین‌های فشاریِ بدون نیاز به ابزار برای نصب هر دو اندازه‌ی فن را اضافه کرده‌ام؛ همچنین فرورفتگی‌هایی برای مهره‌های M3 دارد تا هر دو فن با پیچ نصب شوند. مهره‌های M3 باید شش‌گوش 5.5mm و حداکثر ضخامت 2.5mm داشته باشند. ایده‌ی این پروژه، امکان استفاده از دو فن بی‌صدای 4020 بود. همراه با

متن اصلی طراح (انگلیسی)

Briss Moto design Just to make things clear, my designs are protected by copyrights laws. It is not authorized to distribute or sell any of my designs without prior written authorization from myself. Even if you modified my original design. Thank you DOES NOT FIT NEO 2022-04-20: Ender 3v2 models V4.41, made the support bigger on ender CR touch mount and also made a fix to hold the nut in the fang for the rear hole. 2022-03-30: Corrected the MS linear rail models with proper bulge position. 2022-03-13: update on the Aquila model 4.41 with proper positionning of the holes. But i can't make it compatible with leveling probes, holes position interferes with that. 2022-01-31: I have been notified there might be an issue with the height of the CR touch mount. The mount on the fang is indeed 1.5mm higher than the metal mount supplied from creality. But there should be a 2mm gap between the nozzle and the plate when the CR touch is fully extended. The design intention of the fang is to be 1.5mm higher than the nozzle. If your fang is higher than that this might be the issue. Anyway, i've added a "CR touch spacer" in the STL's for those who want the exact height creality set their mounts at. The BL touch is longer than the CR touch and this spacer should not be needed. Thanks for the feedback everyone. 2021-11-25: update to V4.4 For ender 3 pro, ender 3 max and Ender 3 with microswiss linear rail. V4.4 fang with integrated BL/CR touch mount, the holes don't go through for a very specific reason. It's a single layer that doesn't go through, it allows to print bridges across so you don't need supports to get that part printed properly. Then you trim off the single layer to clear the holes. I did that because when you try to print a bridge that has a hole in the middle it does not print very pretty, or you need to add support which adds a lot of time to the print for nothing. Now it prints well without supports and takes 10 seconds to trim off the single layer for the bolts to go through. Enjoy :) 2021-11-14, V4.4 versions for the Voxelab Aquila, including with BL-touch / CR-touch mount. 2021-11-13 New V4.4 with tip angle corrected for better airflow orientation, Built-in BL-touch/CR-touch mount with additional bolt hole for better rigidity (Offset: X = 44mm, Y = 7.5mm). For Ender 3 V2 and ender 3 microswiss direct drive kit. Update for the other models will follow up. Printing with the built-in CR-touch mount does not require supports at all anymore. There is a small tower support built in the model that you just snip off at the end. Also adding the Microswiss DD spacer without holes for the extruder knob. 2021-05-04: adding Fan duct up V2, which has integrated grill on top. More tricky to print than the original so i'll leave both files here. 2021-05-01: Adding a model that fits Voxelab Aquila and one that fits Microswiss linear rail kit. Still have to design a BL touch adaptor for the Aquila V4.2 -Now compatible with micro swiss direct drive M2601 M2602. You need to print the fang, the spacer and the extruder knob. (will be coming up with a BL touch mount for this configuration in the coming week or 2) -All models available with integrated LED lights (5mm straw hat LEDs up front and possible to put a 20mm star inside). Both files are available, with or without lights. It's a little more tricky to print the one with lights, has small features. -Made the mid bolt tab larger, more robust and easier to print (ender 3 pro and microswiss) -slotted the wire hole for the front fan V4.1 -modified the mounting a little for Ender3 & Ender 3 pro. Now a different file than the Ender 3 V2. -Added a slot for the front fan wires 2021-02-04: Adding a tiny optional add-on part that goes under the hot end fan to complete the duct to get absolute maximum efficiency. leaving this as a separate part from the fang because it would prevent from printing it without support. Just glue it in place after. Compatible with V3 and V4 fang. STL named :BRISS fang V3 V4 flow control. Versions: V4.0 Same geometry as the V3 but with minor improvements for better printability and added a hole for Ender 3 pro (+ BL touch bracket for the 3 pro) -Added insert in the middle of the part cooling fan to reduce turbulence and help with efficiency. -Shifted the Fang a little bit to the left for better centering on the hot end -shortened the hooks a little(mounting points on the right) to make it easier for instalation. -made the insert for the top fan full again to aid bed adhesion -added a bridge to join the chimney to the top fan flange to help those with adhesion issues -made a notch in the hot end cooling duct to help clear the bolt when pivoting it in, easier instalation -made the hole a tiny bit bigger for the front fan wires, allows to pass some tiny bullet connectors. -Added a 2nd hole at the back that aligns with the original Ender3 / Ender3 Pro back plate. -BL touch bracket specific for each versions 2021-01-03 edit: I added the STL for the front fan duct to prevent sucking every debris and filaments from the build plate. Prints without any support, just lay it flat on the fan flange. For installation you need the longer push pins (STL named "holder pin 4020 fan + duct") V3.0 has much larger ducts than the V2. Flows a lot more air to your parts. The duct is also wider so it cools the part properly when doing straight lines in the Y direction. BL touch brackets specific for each versions Sleek compact fang allows the use of dual 40mm fans. Easy to print and easy to use, it's a single part that attaches similar to the original fan cover on the Ender 3 v2. Prints up side down with no supports at all. You can use 10 or 20 mm thick fans. I included the STL file for tool less push pins to fix both size of fans but it also has recesses for M3 nuts to bolt both fans on. M3 nuts should have a 5.5mm hex and maximum 2.5mm thickness. The idea behind this project was to be able to use two silent 4020 fans. Together wit

  • ender3
  • ender3 v2
  • 4020 fan
  • dual 40mm fan
  • fang
  • hot end cooling
  • part cooling
  • cr-10
  • ender 4
  • ender 3
  • ender4
  • ender 3 max
مدل چاپ سه‌بعدی داکت فن هات‌اند Ender 3، 3 V2، 3 pro و 3 max (Ender 3, 3 V2, 3 pro, 3 max, dual 40mm axial fan hot end duct / fang. CR-10, Micro Swiss direct drive and bowden compatible. No support needed for printing) — فایل پرینتر سه‌بعدی (STL)