داکت خنککننده Briss fang Gen2 برای Ender 3، Red lizard، Spider، Revo و dragonfly
Ender 3 Briss fang Gen2, Red lizard, Spider, Revo, dragonfly, etc.
طراح: BrissMoto
قیمت فایل با خرید و تحویل
۶۶۸٬۰۰۰ تومان
- قیمت ارزی فایل
- ۱.۵۹ EUR
- معادل تومانی
- ۴۶۸٬۰۰۰ تومان
- کارمزد خرید
- ۲۰۰٬۰۰۰ تومان
بعد از پرداخت، فایل را برایتان میخریم و در صفحهٔ همین سفارش در حساب شما برای دانلود میگذاریم. چند فایل را با هم در سبد بخرید تا کارمزد یکبار گرفته شود.
مجوز: CULTS PU - Private Use — فقط استفادهٔ شخصی؛ فروش محصول چاپشده مجاز نیست
این طرح کار طراح آن است و مجوز استفادهاش همان مجوز طراح است؛ پخش یا فروش خود فایل مجاز نیست.
دربارهٔ این مدل
An other original Briss Moto design My designs are protected by copyrights laws. It is not authorized to distribute or sell any of my designs without prior written authorization from myself. Even if you modified my original design. Thank you Edit: does not fit ender 3 neo, ender 3 max, ender 3 s1 or any other variations that does not use the same hot end and housing bolt pattern as the original ender 3 or ender 3 v2. 2023-06-06: Adding 55.5mm fang for volcano heat block or dragonfly HIC 2023-04-09: Adding Fang for ender 3 compatible with Revo micro using this mount (https://www.thingiverse.com/thing:5200613) 2023-01-03: Adding printed direct drive bracket for the creality aluminum dual gear extruder. 2022-06-20: Adding fangs compatible with the Micro Swiss direct drive (the standard one, not the NG) and NOT for linear rail version either (that will be coming up later). Also adding a printed direct drive bracket for stock motor and extruder. New fang based on my original and popular design, made to use two 40mm axial fans but made to fit around bigger hot ends and supply twice the airflow for high flow nozzles and high deposition rates. In the following weeks I will design adaptors to use Orbiter extruder and make it fit some more printers. Right now only fits ender 3, ender 3 pro and ender 3v2. -Improved fang support on the right side -Double the airflow -Repositioned hot end fan for increased nozzle visibility -Modular wire management -Modular accessory mounts on each side (BL touch, CR touch, EZABL (coming soon), etc.) BL touch offset: x-54 and Y-27 -Built-in LED mounts for 5mm straw hat LEDs -Still prints with no supports at all, some supports are built-in the model and you snap them off at the end Comes in different length for the different hot ends. ****@ Length measured from the center of the hot end mounting holes to the tip of the nozzle @**** PLEASE MEASURE YOUR HOT END, there are copies, variations and new products released regularly. 51mm : Creality Spyder (Measure your hot end carefully, there are at least 3 versions out there with different size) CR10s pro 49mm: Mellow NF crazy 47mm: Creality Mk8 (stock ender 3 hot end) Creality Spider v2 Red lizard V2 Red lizard V5 pro Phaetus Dragonfly 7 fins (warning, there is a shorter 6 fins version out there too) Phaetus Taichi 45mm: Phaetus dragonfly 6 fins Red lizard Q1 I tested a high flow 4028 fan for parts cooling sanyo-denki 109P0424R3013, Flows more than 5015 blower. Only drawback is that when slicer is set at 1%, it already spins at about 50% of maximum speed. And it's pretty noisy of course at 14000rpm. Please let me know if you have any issues, this is a new design and could need some tweaks. 0.4 or 0.6 nozzle 0.2 mm layer height supports: none Steep 60deg overhangs, harder to print with some materials. proper printer set-up and calibration recommended. 45deg duct is also 60 deg overhang. i recommend using thinner layers, slower print speeds and print with a material that is easy to print with.
- ender3
- ender3 v2
- 4020 fan
- dual 40mm fan
- fang
- hot end cooling
- spider
- spyder
- dragonfly
- nf crazy
- red lizard
- part cooling
- cr-10
- ender 4
- ender 3
- ender4
- revo micro
- revo cr
- revo