رفتن به محتوای اصلی
ارسالات ترکیه: ۸ تا ۱۲ روز کاری

DIY Sandevistan

طراح: macb3lyacob

قیمت فایل با خرید و تحویل

۳٬۱۰۱٬۰۰۰ تومان

قیمت ارزی فایل
۹.۰۹ EUR
معادل تومانی
۲٬۶۷۳٬۰۰۰ تومان
کارمزد خرید
۴۲۸٬۰۰۰ تومان

بعد از پرداخت، فایل را برایتان می‌خریم و در صفحهٔ همین سفارش در حساب شما برای دانلود می‌گذاریم. چند فایل را با هم در سبد بخرید تا کارمزد یک‌بار گرفته شود.

مجوز: CULTS PU - Private Use — فقط استفادهٔ شخصی؛ فروش محصول چاپ‌شده مجاز نیست

این طرح کار طراح آن است و مجوز استفاده‌اش همان مجوز طراح است؛ پخش یا فروش خود فایل مجاز نیست.

دربارهٔ این مدل

Not much to say, I was bored and wanted to make a cool Halloween costume. Yurt. There are magnets inside the print (explained later), and they stick to magnets that you attach to your back using tape. But here's a list of the things I bought to make it. Led Strips: https://tinyurl.com/mv67fecb Led Strips Controller: https://tinyurl.com/5n84v74u Neodymium Magnets: https://tinyurl.com/2s32jhya Battery Pack: https://tinyurl.com/hr4t7e8v Medical Grade Tape: https://tinyurl.com/3u9v5v6e Order of Assembly: Neck Piece, Clip On [NECK], bw Spine and Neck, Clip On [SPINE], Sandevistan D2, Bridge, Sandevistan D1 Made of: PLA- Neck Piece, bw Spine and Neck, Sandevistan D2, Sandevistan D1 TPU- Clip On [NECK], Clip On [SPINE], Bridge When first printing all the PLA pieces 1) Make sure to add support for all the PLA pieces because of the borders they have at the bottom. 2) Make sure you PAUSE the print at around layer 53, or whatever the layer is before the magnet hole is covered to insert your neodymium magnets (6). Then from there, you should be chilling and can let the print build by itself. When making the TPU pieces, the only piece you should worry about building is the bridge because it needs a unique set of supports. Check out the photos to see what they look like. I placed it at a 45-degree angle, blocked the supports on the inside, and added supports on the back that kind of looked like this :|: For the Bridge and Clip-On pieces, a piece of TPU filament should fit through and act as a hinge. The TPU I had used in this case was around 0.1089 in. Each hole in the TPU pieces has a tolerance of +-1 mm (~0.0394 in). To ensure the filament hinges stay intact, I cut them off until there were around 1-2mm left, then soldered them. For the lights, I used a 9.8ft COB LED strip. You should measure out how much of it you're going to need to use, then cut it off at the cut marks. I recommend keeping the wires that are covered by plastic at the end of the lights inside of your SPINE pieces because they're very sensitive to bending and may ruin the soldering. I do NOT recommend taking off the tape of the LED Strips unless it's like an inch for the piece that's near your waist. Inside each of the pieces, there are little borders that allow the lights to slide through smoothly. Extra Diffusion: If you want to diffuse the lights a little more, at the top holes of each of the Sandevistan [SPINE] pieces, there should be tiny ledges inside to slip a tiny layer of translucent paper to diffuse the lights. But make sure to remove the extra filament that covers it. Battery: Now that you're almost done, connect the LEDs to the battery, shove it in your back pocket, take off your shirt, then show everyone how cool you are.

  • anime
  • scifi
  • cyberpunk
  • edgerunners
  • 2077
  • sandevistan
  • sci
  • future
  • 3d
  • print
  • replica
DIY Sandevistan — فایل پرینتر سه‌بعدی (STL)