رفتن به محتوای اصلی
ارسالات ترکیه: ۸ تا ۱۲ روز کاری

نگهدارنده کابل خرگوشی

Bunny Cable Holder

طراح: Holoprops

قیمت فایل با خرید و تحویل

۱٬۷۳۷٬۰۰۰ تومان

قیمت ارزی فایل
۵.۰۹ EUR
معادل تومانی
۱٬۴۹۷٬۰۰۰ تومان
کارمزد خرید
۲۴۰٬۰۰۰ تومان

بعد از پرداخت، فایل را برایتان می‌خریم و در صفحهٔ همین سفارش در حساب شما برای دانلود می‌گذاریم. چند فایل را با هم در سبد بخرید تا کارمزد یک‌بار گرفته شود.

مجوز: CULTS PU - Private Use — فقط استفادهٔ شخصی؛ فروش محصول چاپ‌شده مجاز نیست

این طرح کار طراح آن است و مجوز استفاده‌اش همان مجوز طراح است؛ پخش یا فروش خود فایل مجاز نیست.

دربارهٔ این مدل

This adorable Bunny will hold your favourite cable with commitment. Can't be cuter than that! Perfect for your smartphone, iPad, iPhone cables. Use it wherever you need a little friend to hold your cable: Desk, Table, Kitchen counter, Nightstand or Car Dashboard. At home or the office! Guaranteed 100% Kawaii! (✿◠‿◠) *Your cable will not fit if it exceeds 4mm diameter!* *Make sure you don't want to use it for a large cable. Tested with Apple chargers, Samsung chargers, USB-C and USB-A cables.* If you want to to fit a larger cable, just increase the scale of the bunny until it fits your needs. ⭐⭐⭐⭐⭐ IMPORTANT NOTE: If you want to sell 3D prints based on my designs **legally**, please become a supporter on the Thangs Membership: 🔵[Thangs - Membership](http://tinyurl.com/Holoprops) All my Designs are covered by a Creative Commons Non-Commercial License on Cults 3D. The sale of prints using my designs is the sole right of myself, the designer, and my active supporters to do so. Please understand every design is many days of work and multiple prototype prints to ensure quality. Happy printing! To get the best out of the STL files, please follow these guidelines: • Layer Height 0.2mm • No supports needed, but use a raft for the small parts (eyes, blush and mouth) • Nozzle 0.4mm • Recommended infill 20%. • Do not print over 50 mm/s. A lower speed like 40 or even 30 mm/s will always produce better results. • Make sure your bed is correctly levelled. Then check again :D • Try to hide the seam and place it in the back of the bunny where nobody will pay attention. • Make sure your printing temperature and bed temperature is adequate for the filament you are about to use. • If you follow the recommended settings above, you do not need any supports to print the body. Please, tag me on Instagram (@Holoprops), I would be thrilled to see your results in all kinds of colors. Happy printing! PH from Holoprops

  • cable
  • iphone
  • ipad
  • smartphone
  • samsung
  • holder
  • secure
  • desk
  • nightstand
  • kitchen
  • car
  • home
  • setup cute
  • kawaii
  • bunny
  • cat
  • cables
  • usb-c
  • lightning
نگهدارنده کابل خرگوشی (Bunny Cable Holder) — فایل پرینتر سه‌بعدی (STL)